Wooden Octagonal Gazebo 500x500x330 (L×W×H) · SS-012790
Price on request
SKU: SS-012790
Product Technical Specifications Seating Area: 500 x 500 cm (197 x 197 in) Roof Area: 570 x 570 cm (224 x 224 in) Height: 330 cm (130 in) • Wood Characteristics: The wood material for manufacture will be first‑class Yellow Pine (Pinus sylvestris) lumber. Wood sections will be fabricated with a maximum tolerance of ±2 mm (0.1 in), and wood dimensions with a maximum tolerance of ±20 mm (0.8 in). Required wood qualities include: - Knots: Each meter may contain up to four solid knots; knot diameters will not exceed one‑quarter of the piece width. No rot, defective, partially fused, or fallen knots are allowed. - Cracks: No ring cracks; fine hairline cracks (1‑2 mm (0.1 in)) are permitted. Pressure‑treated environment may introduce head and foot cracks within tolerance limits. - Resin pockets: No more than one resin pocket per meter, not exceeding 10 cm (3.9 in) in length. No dripping or pulling resin, inner bark, rot holes, insect holes, or manufacturing defects beyond the specified tolerances. - Deflection: Deflection will not exceed 1/50 of the member length; impact shall not exceed 1/100 of the member width. - Twisting: Twist will not exceed 2 mm (0.1 in) per meter of length. - Bend in the grain: Tolerated between 1/50 and 1/100 of the member length. - Sanding: All visible surfaces will be sanded smooth. • Main Supports: Eight support legs, each 90 × 90 mm (3.5 x 3.5 in), will be made from pine lumber machined with diamond‑tipped knives and decorative motifs. Support leg height is 240 cm (94.5 in). • Roof: The gazebo’s roof frame will use 50 × 100 mm (2 x 3.9 in) wooden slats. Two corners of each slat will be routed for shaping. The top of the slats will be fastened with wooden cladding or fiber material, then covered with zinc‑treated membranes secured with wide‑head special nails. The roof will be finished with American shingles attached with the same nails. A 30 × 130 mm (1.2 x 5.1 in) decorative wooden fascia, also cut with diamond‑tipped knives, will be mounted on the roof with galvanized wood screws. The roof connection frame consists of eight 50 × 50 mm (2 x 2 in) slats, cut at specific angles and shaped with diamond‑tipped knives, linking the main supports to the fascia. All fixed connections will use stainless‑steel wood screws; connections between the main supports and the roof will use special galvanized wood screws. • Pigeon Loft: The pigeon loft height is 450 mm (17.7 in). Its roof slats are 50 × 50 mm (2 x 2 in) lumber, with additional 30 × 15 mm (1.2 x 0.6 in) wooden battens spaced 30 mm (1.2 in) apart between the upper and lower slats. The slats will be fastened with shiplap cladding, zinc‑treated membranes, and wide‑head nails, then covered with American shingles. The eaves will use 90 × 20 mm (3.5 x 0.8 in) decorative wooden pieces shaped with diamond‑tipped knives. • Upper Panels: Upper railings are 40 cm (15.7 in) wide. Railing frames are 50 × 50 mm (2 x 2 in) lumber, sanded on all sides and edged with decorative diamond‑cut wood. They are mounted to the main supports with galvanized wood screws. Intermediate decorative pieces are 40 × 50 mm (1.6 x 2 in), also cut with diamond‑tipped knives, and attached with galvanized screws. • Lower Panels (Railings): Lower railing height is 75 cm (29.5 in). Frames are 50 × 50 mm (2 x 2 in) sanded lumber with decorative edges, fixed to the main supports with galvanized wood screws. Intermediate decorative pieces are 40 × 50 mm (1.6 x 2 in), installed with galvanized screws and clear specialty wood glue. • Seating Unit: The seating unit consists of eight wooden legs, each at least 4 × 9 cm (1.6 x 3.5 in), attached at one end to the support structure and at the other end to the seating slats. Four decorative wood slats per side will be shaped with diamond‑tipped knives and secured with galvanized wood screws. • Anchoring: Under each support leg a steel flange (18 × 13 × 3 mm (0.7 x 0.5 x 0.1 in)) will be welded to a base plate (15 × 8 × 2 mm (0.6 x 0.3 x 0.1 in)). Two anchor holes will be drilled in a 13 × 8 × 3 mm (0.5 x 0.3 x 0.1 in) plate, and three 6 mm (0.2 in) screw holes will be drilled in each 15 × 8 × 2 mm (0.6 x 0.3 x 0.1 in) plate. Anchors will be fastened with screws to the footings, and the structure will be tied to the ground with steel dowels. This prevents wood contact with moisture and secures the support legs. Gazebo anchors will be welded with a minimum 2.5 mm (0.1 in) fillet weld on both sides of the flange. Each leg will receive six specialty screws for anchoring to the verticals and two dowel screws for ground attachment. All metal parts will be powder‑coated with polyester‑based paint. • Impregnation: [Further details not provided]