Wooden Gazebo Octagonal 500x500x330 (L*W*H)
Price on request
SKU: SS-012731
Product Technical Specifications Seating Area: 500 x 500 cm (197 x 197 in) Roof Area: 570 x 570 cm (224 x 224 in) Height: 330 cm (130 in) Wood Characteristics: - Primary material: 1st‑grade Yellow Pine (Pinus sylvestris) lumber. - Wood sections are cut with a maximum tolerance of ±2 mm (0.1 in); dimensions with a tolerance of ±20 mm (0.8 in). - Knot allowance: up to four sound knots per meter, each not exceeding ¼ of the part width. No rotten, split, partially fused, or missing knots. - Cracks: No ring cracks; hairline cracks (1‑2 mm (0.1 in)) are permissible, as are pressure‑treated crack types within tolerance limits. - Resin pockets: Maximum one per meter, not exceeding 10 cm (3.9 in) in length. No dripping or pulling resin, inner bark, rot cavities, or insect holes. - Manufacturing defects are excluded; only allowable tolerances apply. - Deflection: Not to exceed 1/50 of the member length; impact marks not to exceed 1/100 of the member width. - Twist: Not to exceed 2 mm (0.1 in) per meter of length. - Bending of the edge: Tolerated between 1/50 and 1/100 of the member length. - Sanding: All visible surfaces will be sanded smooth. Main Supports: - Eight support legs made from 90 × 90 mm (3.5 x 3.5 in) pine lumber, cut with diamond‑tipped blades and featuring decorative motifs. - Support leg height: 240 cm (94.5 in). Roof: - Roof bearing beams built from 50 × 100 mm (2 x 3.9 in) wood, milled on two corners for shaping. - Beams are covered with wooden tongue‑and‑groove paneling or fiber material and fastened with screws. - Zinc‑coated nails install tar‑impregnated membranes, then American cedar‑shingle roofing. - The fascia board (minimum 30 × 130 mm (1.2 x 5.1 in)) uses decorative, diamond‑tipped wood slats secured with galvanized wood screws. - Roof connection framework: eight 50 × 50 mm (2 x 2 in) slats, cut at specific angles, attach one end to the main support and the other to the fascia. - All fixed connections use stainless‑steel wood screws; roof‑to‑support joints use special galvanized wood screws. Pigeon Loft: - Height: 450 mm (17.7 in). - Roof slats: 50 × 50 mm (2 x 2 in) wood. - Additional upper and lower slats: 30 × 15 mm (1.2 x 0.6 in) spaced 30 mm (1.2 in) apart. - Slats are fastened with tongue‑and‑groove boards, tar membranes, and zinc‑coated nails, then covered with cedar‑shingle roofing. - Eaves board: 90 × 20 mm (3.5 x 0.8 in) wood shaped with a diamond‑tipped decorative blade. Upper Panels (Railings): - Rail width: 40 cm (15.7 in). - Rail frames: 50 × 50 mm (2 x 2 in) wood, sanded on all sides, edges beveled with diamond‑tipped blades, and mounted with galvanized wood screws. - Intermediate motifs: 40 × 50 mm (1.6 x 2 in) decorative wood pieces installed with galvanized screws. Lower Panels (Railings): - Height: 75 cm (29.5 in). - Frames and intermediate motifs are the same as the upper panels, fastened with galvanized screws and transparent wood glue. Seating Unit: - Eight 4 × 9 cm (1.6 x 3.5 in) L‑shaped wooden legs, each attached one end to the main support and the other to a seating rail. Four decorative, diamond‑tipped wooden slats per side are secured with galvanized screws. Anchoring: - Under each support leg a 18 × 13 × 3 mm (0.7 x 0.5 x 0.1 in) flange is welded to a 15 × 8 × 2 mm (0.6 x 0.3 x 0.1 in) plate; two anchor holes are drilled in a 13 × 8 × 3 mm (0.5 x 0.3 x 0.1 in) plate, and three 6 mm (0.2 in) screw holes are drilled in each 15 × 8 × 2 mm (0.6 x 0.3 x 0.1 in) plate. - Anchors are bolted to the supports and to the ground with steel dowels, preventing water contact and providing stable footing. - Flanges are welded on at least two sides with a minimum 2.5 mm (0.1 in) weld. - Each leg receives six dedicated anchoring screws; two additional dowel screws secure the structure to the ground. - All metal components are powder‑coated with polyester paint and baked. Impregnation: (details omitted)